Fire control program

Jobs in Karachi. Jobs in Lahore. Post Jobs. Resident Engineer Construction Company. Accounts Officer Construction Company. Sub Engineer Construction Company. Clerk Construction Company. Computer Operator Construction Company. Office Boy Construction Company. Additional Director Overseas Pakistanis Foundation. Assistant Director Overseas Pakistanis Foundation. Registrar Government College University. Security Guard Gujrat Gymkhana. Security Guard Pathway Manpower Services.

Deputy Director Government College University. Staff University Of Agriculture. Fire Fighting Technician Hasilpur Corporation.

Junior Clerk Agricultural Research Institute. Driver Tangent Recruitment Agency. Driver State College Of Nursing. Consultant Energy Department. Physiotherapist Jinnah Hospital. Junior Clerk Agriculture Research Station.

Sanitary Worker Civil Defence Department. Naib Qasid Civil Defence Department. Driver Civil Defence Department. Chowkidar Civil Defence Department.

Gardener Civil Defence Department. Siren Operator Civil Defence Department. Medical Officer Pakistan Based Company. Vice Chancellor Cecos University. Hygiene Promoter Non Governmental Organization.

Distribution Officer Non Governmental Organization. House Job Capital Development Authority. Reporting Officer Non Governmental Organization.

Finance Officer Non Governmental Organization. Community Worker Non Governmental Organization. Protection Officer Non Governmental Organization. Step Jog Mode is used for fine adjustment to the torch carriage position that is not possible in continuous jog mode. To move a given step distance, select the desired step distance and click an arrow key direction or use the keyboard shortcut buttons. Pressing the Tab key again will cycle back to continuous jog mode.

The Program Toolpath Visualizer is used in FireControl to display the toolpath of a loaded program as well as the current torch position in relation to the cutting program. Cutting toolpaths are shown in orange color, rapid moves are shown as blue lines, and the current torch position is shown as a white crosshair.

The visualizer will be blank until a cutting program is loaded into FireControl. Below the visualizer window are three buttons; Fit, Zoom-in, and Zoom-out. The toolpath visualizer can be panned around the window by left clicking and holding while moving the mouse around. To zoom the visualizer in and out, click the zoom-in and zoom-out magnifying glass icon buttons below the Toolpath Visualizer.

If you have a mouse with a scroll wheel click, the visualizer window and scroll up on the scroll wheel to zoom in and scroll down to zoom out. The toolpath visualizer is a useful tool when running programs to verify that everything is correct with your program before and during a cutting cycle. We suggest that after zeroing a program, you manually jog the torch around the machine bed to verify that your cutting program will fit within your available material by following the crosshairs on the screen.

The G-code Display window shows the lines of g-code when a program is loaded into FireControl. When a program is running, FireControl will scroll through the lines of g-code as they are executed by the controller with the current g-code line being highlighted while running. The G-code Display window can be a valuable resource tool for manually checking lines of g-code before running a program.

Before running a program, make sure that your torch is first zeroed in a good position on the machine bed relative to your work piece.

Verify that your plasma torch cable has enough slack in the Cable Support Tube to traverse the length of the cutting program without binding and that your plasma cutters work clamp is attached to the drain plug of the water table. Ensure that nothing within range of the plasma cutting arc is flammable and that you keep your hands away from pinch points on the machine when in motion.

Consult your plasma cutter manufacturers guidelines for safe operating instructions and for the appropriate personal safety equipment when operating your plasma cutter. From here you can select your program to upload by following the onscreen prompts. If successful, the program will be loaded and will show in the Toolpath Visualizer window. If your program has an error, FireControl will let you know the error and the line in the g-code file where the error is present.

In order to cut a program in FireControl, you will need to generate your program using a Langmuir Systems approved post processor for your CAM software or else it will not run visit our Downloads page for access to our Fusion and SheetCAM post processors for FireControl.

A program generated without the use of our post processor will lack the necessary g-code formatting, IHS loop functions, and THC activation codes. Pausing and Stopping a program while cutting will automatically shut the torch off for safety reasons. The Real-time Overrides menu is used to make adjustments to your cutting program while the program is currently running.

Feed Rate override is used to slow down or speed up the feed rate of a program while it is cutting. The Pierce Delay Override is used to increase or decrease the pierce delay duration while a program is running. The overrides can be reset back to default by clicking the reset icon to the right of the current override percentage. The Manual Torch Fire button can be used to manually fire your plasma torch from FireControl software. Once enabled, the torch can be fired and turned off by clicking the Manual Torch Fire button again.

Before clicking the button, reference the DRO for XY position to ensure that your torch has a safe path back to the expected zero position. This can be useful to trim down larger sheets of material for more convenient cutting or simply to make quick straight cuts on parts. Run From Here mode can be used to start a program from a point point other than the beginning of the program. This can be useful if you need to pick up a cut in the middle of a program without having to start at the very beginning.

Since a cut program cannot start in the middle of a cut loop, FireControl will automatically determine the start of the cutting loop for the line that you have selected and ask you to confirm this start point.

After confirming, FireControl will load the new program starting with the cutting loop that you highlighted in the previous step. Manual NEST Mode can be used in FireControl to cut several parts from the same program next to each other without having to reset your zero position each time. This allows you to select the direction that you want to cut your next part relative to the part you just cut.

This process can be repeated over again until you have cut the desired quantity of parts. The image below shows several parts cut using Manual Nest Jog. FireControl has a built-in alarm system in conjunction with the USB Motion Control Board to throw an alarm when something goes wrong see below.

You will not be able to move your machine around again until an alarm is cleared. We suggest troubleshooting the alarm issue with your machine and disconnecting and reconnecting your machine connection before continuing. FireControl has several built-in keyboard shortcuts which make it easier to operate, especially if you have a wireless keyboard that can be used as a pendant for jogging.

These shortcuts can be accessed from the FireControl help menu for quick access and they are also listed below. Your version of FireControl will be listed along with a link to our Downloads page to check if a newer version of FireControl is available for installation. Toggle navigation Store. Video overview of the main user interface of FireControl. Make sure your computer meets the following system requirements.

System Requirements. Height Control. Manual Connect If your CrossFire CNC electronics box is plugged into your computer but fails to auto-connect, you may need to manually connect the device.

Disconnecting and Resetting Connection At any time during operation you can reset or disconnect your CrossFire machine from the FireControl software. FireControl-compatible machines have an electronics enclosure with Z-Axis motor port. Legacy CrossFire machines require the use of Mach3 as control software.

Ensure that if you are using a Windows 7 or 8 computer , you have installed the proper drivers available for download on our Downloads Page. You are now fully connected. If FireControl does not fully connect and the 'CrossFire' text is slightly greyed out without listing the Firmware version: Wait 10 seconds with FireControl open for the Connection Help button to appear.

Click this button and select the option to re-flash the firmware. You may need to restart FireControl after this operation. Open Windows Device Manager. You can search the Start menu for 'Device Manager' to locate this application. The expected devices are shown in the image below.